How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with the keyless entry feature built in. This key is similar to remote controls and can be exchanged by an Kia dealer.

Key fobs can stop working for several reasons, including a dead coin battery, worn buttons signals, water damage, signal interference and a damaged receiver module. Here are some suggestions to assist you in getting your Kia sportage replacement key to work again.

How to replace the remote key or the smart key?

Whether your 2012 Kia Soul key comes with an intelligent key, remote key push-to-start key, or a regular non-transponder steel key the battery in these keys will eventually need replacement. This is especially when your car displays a message telling you that the remote or smart keys are not powered by batteries.

It's a fairly simple process. To replace the battery in the key fob, remove the mechanical key from the hole in the back of the key fob. Then lift the cover. A small screw will be located inside the key fob that holds the battery in place. With a small screwdriver, loosen the screw and pull out the battery that was in place. Then, insert the new one and close the slit inside the key fob.

When the key fob is equipped with new batteries and you've tested it, press the locks and unlock buttons. You're in good shape If the doors lock and unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become chilly or when you need to do some errands in Brandon.

Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of steel) are not required for programming. If your key requires to be reprogrammed, you must know the key code number that is stamped on the tag that identifies the key and then record it in a safe place.

How do I replace a battery

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a sign that the battery should be replaced. A battery that is not functioning properly could cause other issues like the check engine light turning on or delayed engine cranking. Fortunately replacing the key fob battery is a fairly simple DIY project that requires just the most basic tools.

Make sure you turn off your vehicle and close the doors before you begin. Find the small metal or a plastic piece on the bottom of the key fob. Jiggle it until the key is released. Then, you can insert this key into the door handle of the driver to unlock your car.

To replace the key fob's battery, remove the cover on the rear and use a pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery and orient the new one in a way that the "+" positive side is facing you, and the "-" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or bending the contacts made of metal.

Once the new battery is installed, turn the key fob off and back on in the ignition for a few times until the door locks. Then you can test your Kia key fob and see whether it's functioning properly again.

How can you replace the smart key?

There is a possibility of having the standard keyfob or Smart Key based upon the model of Kia Sportage. The difference between these is that the smart key is equipped with tiny mechanical key blade that is hidden inside, while the standard key fob does not. Both kinds of key fobs contain batteries that eventually will need to be replaced. It's an easy process that takes just two minutes.

Before you get started it is important to ensure that you are on a flat surface with adequate lighting and that the kia smart key is off. Remember that the fob can contain small pieces that could fall when you're not careful.

The first step is to find the small release button on the lower backside of your fob. It can be an oval silver button or a rectangular slot. Once you press this, the mechanical key blade will pop out and you can then open the key fob.

After the key fob has been open, remove the old battery. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. Once you're done, your key fob will allow you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How do you replace the mechanical key

The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car by simply pressing one button. Like all devices like a key fob, the Kia might have issues. There are ways to address these issues and keep your key fobs functioning for many years.

One of the most common issues is a low or dead battery. The battery could cause the device to stop working or work intermittently. If this is the problem you should replace the battery an entirely new battery.

If this doesn't solve the issue, try using a flathead screwdriver standard to wedge the plastic casing of the fob open. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed then replace it with a new one.

When the new battery is in, close and then open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that can fit in the slot). Test the key fob to ensure it's functioning properly. If the device isn't working, contact a dealer or locksmith to help resolve the problem. Make sure they make you an emergency key that can work across all trunk and door cylinders in order to avoid lockouts again.