15 Surprising Facts About Double Glazing Door Lock Repairs

Double Glazing Door Lock Repairs

Has your uPVC window or door mechanism deteriorated? Perhaps the door Jerealas or window handles aren't aligned properly or are hard to use.

It's important that your double glazed doors function smoothly, or else you'll lose energy and increase the chances of burglary. Owen the Locksmith can fix your door lock at a reasonable price.

Snapped Key

It can be a hassle when a key gets stuck into the lock. This can also be a security risk, as it may leave you vulnerable to burglars if your door does not lock. Fortunately, there are some quick fixes that you can use to solve the problem and get your door functioning properly once more.

Be calm. If you panic, you could end up pushing the damaged key piece further into the lock.

Spray WD-40, or any other penetrating lubricant, Jerealas.Top into the lock. This will allow the broken piece to emerge more easily. You can also employ a screwdriver in order to break up any pieces stuck that might be hindering the flow. If you have a chunk of the key stuck out then grab it using the help of a paperclip or any other thin metal object and pull it. Both methods work, but you must be careful not to push the broken key further into the keyway.

Some paperclips come with grooved edges that can be used as hook extractors. Jigsaw blades can also work well for this. If you don't have one of these tools, you can bend a hook with needle-nosed pliers. Finally, a pair of tweezers is a good way to grasp and pull out the remaining part of the broken key.

If you cannot remove the broken piece of key, use a lock deicer. This is usually available at all hardware stores. It is used to freeze any moisture or ice that may be in the lock.

If none of these strategies are working you, it's time to call a locksmith. Fitlocks experts can fix issues such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also reconfigure your double glazing door mechanisms to make them more user-friendly. Get a double glazing repair with us online or give us a call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose a serious security risk. A professional locksmith can easily fix the cylinder. To fix the cylinder, locksmiths must tap it. They can do this using the hammer or any other tools, but the most effective way is to employ a long match or piece of wire. The match or wire end near the keyway. The locksmith will then strike the lock in order to break it. This is much better than using a heavy hammer, which could harm the lock.

The most frequent cause for cracks in the head of a cylinder is due to overheating. This can occur when the cylinder head and block are made of various metals, such as cast-iron or aluminium. When various metals heat up and cool down at different rates, it may create hotspots locally that expand faster than the rest of the head of the cylinder, leading to cracks.

Corrosion is a different cause of cylinder fractures. If the head and block of a cylinder are not maintained in a timely manner, they can rust or corrode, which can cause them to expand more than anticipated. As time passes, this may also lead to cracks.

If your uPVC window or door lock is brittle and requires a lot more pressure to turn it could be due to a variety of causes. This can be caused by a faulty locking mechanism or misalignment, or a worn-out handle.

Fortunately, this is an easy and inexpensive fix for most homeowners of double glazing. A professional locksmith should be able to resolve the issue within an hour after arriving at your residence. Based on your requirements they will be able to replace the locking mechanism, change the window handles, and also change the gearboxes. A professional locksmith will always be able to advise you on the most cost-effective solution for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders, which offer an additional layer of protection from burglars. This is a small cost to pay for the peace of mind that comes from knowing your uPVC doors are safe.

Broken Handle

Window handle locks are complex mechanisms that become less effective with time and use, so it's not a surprise they occasionally break. If yours is damaged it may be difficult to pinpoint the cause of the problem and make sure that you repair it correctly.

The issue could be in the internal locking mechanism or the latch, fixing the broken handle will improve your uPVC double glazing door's security and allow you to stop drafts. Incorrectly repairing or replacing your handle can be expensive and could damage the door's frame and lock, so it's worth taking some time to do it correctly.

With the window in the open position, loosen the screw that holds the handle using the screwdriver. This should be located on the inside of the back plate, which is usually hidden by an aesthetically pleasing cover for the screw reasons. It is not recommended to lose any internal parts of the handle such as the levers and plates on either side. Ideally, keep them in the same order so you can replace them again if needed.

Then, turn the handle to make it 90 degrees to the window frame and loosen the screw on the back of the handle that holds it to the internal spindle with a second screwdriver. Once this is loose, you should be in a position to pull the handle off and take out the broken spindle. Replace it with a new one, making sure it is the same length as the previous one (you will typically find them online or in hardware stores) and screw it securely into the correct position. Do not overtighten the screw as this could cause damage to the handle and window frame.

Ensure the new handle is correctly fitted Close the window and test the handle. It is likely that it will operate smoothly and jerealas you'll be able to open your window again.

While you're working on the handle, Jerealas.top make sure to check your uPVC windows are shut properly. If they aren't closing properly, you may experience draughts or damp in your home. Also, you could be compromising the energy efficiency of your home. A local window company, such as Core Sash Windows, will be capable of adjusting the hinges on your window frames so they are able to shut properly.

Broken Spindle

It is more likely for the spindle to break rather than the handle. This is particularly common with uPVC tilt-and-turn windows. These windows require a handle that operates an locking device within the frame of the window. The handle is attached to a centre rod that triggers a set of mushroom-like locking cams, these secure the frame of the window. If the dead latch mechanism is not able to open after the handle is turned, it's likely the spindle has been damaged. This could be a frustrating issue.

There are ways to fix this issue. A reputable locksmith will be able to quickly and efficiently repair this problem. They can remove the window handle using a tool that removes the wheel part of the mechanism that is where the spindle goes. This can be done without damaging the handle or causing other damage to the window frame.

After the wheel has been removed, the technician will inspect the spindle and determine what caused it to break. This involves disassembling the spindle and inspecting each component part, noting any damage or excessive wear. This procedure is usually performed in a clean, well-lit room by highly skilled technicians.

The next step is to clean the damaged spindle. This will remove any debris or dirt that may be obstructing it from working normally. Following this the spindle is cleaned, it can be repaired or replaced. If it is replaced, the technician could use an identical dowel size to the original and drill mating holes into both parts of the spindle. This ensures that the new spindle is precisely matched to the handle.

If the damaged spindle cannot be repaired, it could require replacement completely. Home centres sell generic replacements. However, if the style of your window is unusual then it will be necessary to speak with a woodworker or cabinet maker who can duplicate the exact component for you. Once the new spindle has been installed it can be positioned to the handle by line up the screw holes in the handle with the frames existing screws. Once the handle is seated, you can operate your uPVC windows.